Accelerator Master Batch R100


		Rubber & PTFE Component
		Rubber Chemical
		Accelerator BSM
		Accelerator BSB
		Accelerator DCS
		Accelerator DPG
		Accelerator F
		Accelerator HBS
		Accelerator MBT
		Accelerator MBTS
		Accelerator MS
		Accelerator TMT
		Accelerator ZDBC
		Accelerator ZMBT
		Antioxidant 445
		Antioxidant A100
		Antioxidant B Rod
		Antioxidant BL
		Antioxidant BL75 S
		Antioxidant BLN
		Antioxidant MBI
		Antioxidant ODPS
		Antioxidant SP
		Antioxidant TQ
		Antioxidant ZA
		Antioxidant ZC
		Peptizer Accimel E
		Peptizer Accimel
		Retarder RE
		Tackifier CH
		Active Zinc Oxide
		ADC Blowing Agent
		Stearate
		Chemical - Master Batch
		Rubber Accelerater R 100
		Rubber Accelerater R 170
		Chemical - Modified Sulphur
		CCS
		ICS
		Chemical - Modified Resin
		Resin 300 M
		Resin 300 T
		Resin 500
		Resin 400
		Rubber Compound
		NBR - PVC Polymer Blend
		Reclaim Rubber
		Rubber Polymers
		Precipitated Silica
		Oil & Lubricant
		Zeolite

ACCELERATOR MASTER BATCH R 100

R100 is an accelerator blend recommended for EPDM rubber to give very high tensile strength as compared to the

conventional curing system used. It is also found to be very cost effective and has no detrimental effect on hot air

ageing. Maximum phr recommended is 4.0

Mixing Cycle:

All the above rubber accelerator blends should be mixed at the last stage of mixing. It is preferred the master

batch is matured for 24 hrs before adding these accelerators. Whenever applicable, sulphur can be immediately

added after that. No special care is needed to mix these Accelerators.

Application:

• Microwave / Autoclave Cured Profiles

• Molded Goods

• Gasket

• Transfer Molded Products ETC…

Please refer to the chenge in properties shown in the example below:

Formula:

EPDM H-511:100, ZnO:5, Stearic Acid:1.5, HAF(N330):80, Paraffinic Oil:25, MBTS:2, MBT:2, ZDC:1, TMTD:0.5

Properties	Normal	R100
Accelerators R100 Sulphur	As Above - 1.8	- 3.0 2.0
Rheumatic Test Report
Temperature °C a. Scorch Time, Ts2, Mins. b. Cure Time, Tc90, Mins. c. T Min. in lbs d. T Max. in lbs	160 1.51 13.21 25.73 113.87	160 1.58 14.54 22.66 95.98
Curing Temperature °C/Time, Mins. a. Hardness (Shore A) b. Tensile Strength (kg/cm²) c. Elongation at Break (%)	160 / 14 70 138 420	160 / 15 70 175 420
Blooming Characteristic	Heavy Bloom	No Bloom

Formula:

EPDM H-511:100, ZnO:5, Stearic Acid:1.5, HAF(N330):80, Paraffinic Oil:25, MBTS:2, MBT:2, ZDC:1, TMTD:0.5

Properties	Normal	R100
Accelerators R100 Sulphur	As Above - 1.8	- 3.0 2.0
Rheumatic Test Report
Temperature °C a. Scorch Time, Ts2, Mins. b. Cure Time, Tc90, Mins. c. T Min. in lbs d. T Max. in lbs	160 1.51 13.21 25.73 113.87	160 1.58 14.54 22.66 95.98
Curing Temperature °C/Time, Mins. a. Hardness (Shore A) b. Tensile Strength (kg/cm²) c. Elongation at Break (%)	160 / 14 70 138 420	160 / 15 70 175 420
Blooming Characteristic	Heavy Bloom	No Bloom

		Packaging : 25 Kg. in HDPE lined Paper Bags